Is your kitchen or bathroom looking a little…blah? A penny round backsplash can add instant charm and personality. And guess what? You can totally do it yourself! This guide breaks down the process into easy-to-follow steps, perfect for the busy pet owner (we know how little free time you have!).
Getting Started: Prep is Key
Before you even think about touching a tile, proper preparation is crucial. This will make the entire installation process smoother and help ensure a professional-looking result.
Gather Your Supplies
Here’s what you'll need:
- Penny round tile sheets (measure your space and add extra for cuts and breakage – about 10% extra is usually safe).
- Tile adhesive (check the tile manufacturer's recommendations).
- Grout (again, follow tile recommendations).
- Grout float.
- Notched trowel (the size will depend on the tile; check adhesive instructions).
- Wet saw (renting one is usually the most cost-effective option).
- Sponge.
- Buckets (for mixing and cleaning).
- Level.
- Measuring tape.
- Pencil.
- Safety glasses.
- Gloves.
- Drop cloths (protect your countertops and floors!).
- Painter’s tape.
- Optional: Tile spacers (for extra consistent grout lines).
Prepare the Surface
- Cleanliness is next to godliness: Make sure the existing surface is clean, dry, and free of any grease, dust, or old adhesive. Use a degreaser if necessary.
- Smooth it out: Patch any holes or imperfections with patching compound. A smooth surface is essential for proper tile adhesion.
- Prime time: Apply a tile primer to the surface. This will improve adhesion and prevent moisture from penetrating the wall.
Installing Your Penny Round Backsplash
Alright, let's get tiling!
Layout is Everything
- Dry run: Before applying any adhesive, lay out a few sheets of tile to visualize the pattern and ensure it fits properly. Adjust as needed.
- Find your center: Determine the center point of your backsplash area. This will help you create a symmetrical layout. Use a level and pencil to mark a vertical line.
- Plan your cuts: Pay close attention to areas where you’ll need to make cuts, such as around outlets, windows, or corners. It's best to plan these out ahead of time to minimize waste.
Applying the Adhesive
- Follow instructions: Always read and follow the adhesive manufacturer's instructions carefully. Different adhesives have different application requirements.
- Trowel technique: Use the notched trowel to apply a thin, even layer of adhesive to the wall. Hold the trowel at a 45-degree angle and create ridges.
- Work in small sections: Apply adhesive to only a small area at a time, about 2-3 square feet. This prevents the adhesive from drying out before you can set the tiles.
Setting the Tiles
- Press firmly: Carefully place the tile sheets onto the adhesive, pressing firmly to ensure good contact. Use a grout float or a rubber mallet (with a soft cloth underneath) to gently tap the tiles and level them.
- Use spacers (optional): If you want perfectly uniform grout lines, use tile spacers between the sheets.
- Cut with care: Use a wet saw to make accurate cuts for edges, corners, and outlets. Always wear safety glasses when using a wet saw.
- Pet hair patrol: If you have pets, especially cats, they will try to investigate. Keep them out of the work area as much as possible to avoid paw prints in the adhesive.
Grouting and Finishing
- Wait patiently: Allow the adhesive to dry completely according to the manufacturer's instructions (usually 24-48 hours) before grouting.
- Mix it up: Mix the grout according to the manufacturer's instructions. Aim for a smooth, peanut butter-like consistency.
- Apply the grout: Use a grout float to spread the grout over the tile surface, pressing it into the grout lines. Work diagonally across the tiles to ensure the grout fills the lines completely.
- Wipe away excess: After about 15-30 minutes (or as recommended by the grout manufacturer), use a damp sponge to wipe away the excess grout. Rinse the sponge frequently in clean water.
- Polish and buff: Once the grout has dried completely (usually 24-48 hours), use a clean, dry cloth to polish the tile surface and remove any remaining grout haze.
- Seal the deal: Apply a grout sealer to protect the grout from stains and moisture.
Congratulations! You've just installed a gorgeous penny round backsplash. Now, step back, admire your handiwork, and maybe give your furry friend an extra treat for being so patient (or at least, trying to be).